Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian Ukrainian

Modda Icom id-5100

ID-5100D/A/E Frequencyexpansion

RX Frequencyexpansion

Frequencyrange:   118.000–136.995MHz[AM]

137.000– 174.000MHz[FM]

375.000– 550.000MHz[FM]


Remove D316, after that, key operation


Key operation only


Remove D316, after that, key operation


No need of Modification


Key operation only


No need of Modification


1. Turn off the radio

2. Left AFVR set to 9:00 oclock, and Left SQLVR set to counter clockwise.

3. Right AFVR set to9:00 oclock, and Right SQLVR set to12:00 oclock

4. Turn on the radio by pushingPOWERkey,during touchHOME

TX Frequencyexpansion

137.000– 174.000MHz[FM]
400.000– 470.000MHz[FM]


Remove D312and D310


Remove D312and D310


Remove D312and D310


Remove D312and D310


Remove D312and D310


Remove D312and D310

ID-5100E D-STAR Mobile Firmware Update (Release E2)

Ny uppdatering till ID-5100 ..

läs hela artikeln här

ID-5100E D-STAR Mobile Firmware Update (Release E2)

1. DV Fast Data setting has been added.
2. Near Repeater Search function has been improved.
3. Tone squelch (TSQL) is now supported when using FM repeaters in the DR function.
4. [TONE] FUNC key is now displayed when using FM repeaters in the DR function. (Only ID-5100E)
5. A “to me: Alarm/High Tone” option has been added in the Standby Beep function, and is set as the default.
6. Receive history screen default has been changed from call signs to names.
7. Receive history screen setting is now saved.
8. A function has been added in the DV mode to display the distance between you and the other station from GPS data that is in the recorded audio files.
9. GPS Record Sentence option has been added in GPS Logger.
10. External GPS option has been added to GPS Select in GPS Setting to support an external GPS receiver input from the DATA jack.
11. The Save and Load speed of icf setting files and CSV repeater list files to/from an SD card is faster.
12. Beep tones sound when pushing the headset PTT on a non-Icom Bluetooth headset.

CS-5100 Rev. 1.10 Updated cloning software

1. DV Fast Data setting has been added.
2. A new setting has been added to display either the registered names or the call signs in the Receive History Log.
3. A new alarm tone Stand-by Beep option has been added to Sounds in Digital Setting.
4. An External GPS option has been added to GPS Select in GPS Setting.
5. A Record Sentence option has been added to GPS Logger in GPS Setting.
6. A TSQL option has been added to the Tone selection in the FM Repeater List.

Icom ID-5100

Icom’s New Touch screen ID-5100 Dual Band D-STAR Mobile Radio

Klicka för större bild





Icom are pleased to announce details of the new ID-5100 dual band D-STAR mobile.
As with Icom’s latest range of products, this new model has a new generation design and
a range of features including large, responsive touch screen LCD,
Bluetooth connectivity and second station control through an Android device*.

 Intuitive touch screen operation

The intuitive touch screen interface provides quick and smooth operation for setting and editing various functions and memories. Qwerty keyboard
The 5.5 inch display (320 × 128 pixel) shows a large easy-to-see software keypad (Qwerty keyboard), and allows you to input alphanumeric characters quickly.


V/U, V/V, U/U Dual receive

The ID-5100A receives 118–174MHz and 375–550MHz* with dual receiver capability that allows you to receive two bands simultaneously (including within a single band)*. Almost all VHF & UHF communications are available to you!
*See specifications for receive range coverage.

DV Dualwatch

The ID-5100A has simultaneous receive for FM/FM and FM/DV modes, and the capability of monitoring two DV signals. The main band audio has priority, if two DV signals come in at the same time.

FM/DV Dualwatch
DV/DV Dualwatch (DR function)
FM/DV Dualwatch (DR function)


GPS receiver

Received position information exampleThe ID-5100A/E has integrated GPS which allows you to transmit and receive position data from the built-in GPS receiver. Position, course, speed and altitude are shown on the display.
The GPS position information can be used for exchanging position reports, tracing the GPS log and searching for nearby repeater sites.
The GPS antenna is located in the remote head, no external GPS antenna required.

DV/FM Repeater list function

The DV/FM repeater list function assists you in accessing near-by repeaters, even where you are visiting an area for the first time. The function searches for near-by repeaters using the repeater memories with the GPS position information.
To use the repeater list function, the position data of the repeater is required in the repeater list. The ID-5100A/E will be shipped with a limited number of repeater memories preprogrammed.

Dplus reflector linking

Dplus Reflector link commands are added to the DR function to allow easy reflector operation. Use Reflector, link/unlink to Reflector, echo test and repeater information commands are selectable.

Built-in CTCSS/DTCS encoder and decoder

Built-in CTCSS and DTCS tones are used for accessing a closed repeater or tone squelch operation.
The pocket beep alerts you with a beep sound when the transceiver receives a preset tone. 1750Hz tone is also available.

Reflector commands

UT-133 Bluetooth® unit (option)

UT-133This The UT-133 is the optional Bluetooth® board necessary for operation with the optional VS-3 headset and the optional RS-MS1A, Android™ application.

VS-3 Bluetooth® headset (option)

The optional Bluetooth® headset, VS-3, can be used for hands-free communication and remotely control the ID-5100A/E with three programmable buttons.
Providing you with convenient communication in a vehicle.

RS-MS1A Android™ application (optional free download from Google Play™)

Connect to the ID-5100A/E for remote control of DR functions, link with a map application and send/receive messages and images over the DV mode.
*Optional UT-133 Bluetooth® unit must be installed in the ID-5100A.
*Some functions may not work properly, depending on Android™ phones and
devices used.

Steps to send a picture over DV mode

Steps to send a pictur over DV mode

 Data transfer speed

Other features

  • Menu-driven user interface
  • DTMF via microphone or ID-5100 display
  • Enhanced D-PRS functions with object, position, item and weather formats
  • Convenient memory contents management using CSV data format
  • Speech function announces operating frequency, mode and received callsign (DV mode)
  • Independent main dial, volume and SQL knobs for A/B bands
  • AM airband dualwatch
  • CS-5100, cloning software supplied
  • 50W output power on both VHF and UHF bands

Beräknad leverans för Sverige är April / Maj 2014

Se Film

Uppdatera din ID-5100

Dags att uppdatera din ID-5100 rig


  1. Fixed the problem where the RS-MS1A does not display pictures and text received by the ID-5100 when the SP2 external speaker jack is in use.

  2. Fixed the problem where the D-PRS data in the B band Single watch mode, and/or the right side band Dualwatch mode, may not be recognized.

  3. Fixed the problem where RX sensitivity decreases in the Single watch mode.

  4. The calibration area on the touch screen has been revised to help the user make a more accurate screen calibration.

    An OPC-2218LU or OPC-1529R is required to install the firmware update. To use the OPC-2218LU, a USB driver is required. Download the driverhere.
    Before downloading, please thoroughly read "Firmware update instructions (here)" to know what the update requires.Save the transceiver's data onto an SD card or to your PC using the CS-5100 cloning software.It is possible that your data could get lost or corrupted during the update.Never turn OFF the equipment power or disconnect the data communication cable during the update.The CPU M firmware is updated to Version 1.05.The CPU C firmware is updated to Version 1.01.

    En enkel ritning för att göra din egen kabel

    En USB kabel Från RT System går alldeles utmärkt att använda också , kolla först i enhetshanteraren vilken com port som kabeln tilldelas och välj den porten när uppdateringsprogrammet startas.Läs hela instruktionen innan du börjar ..

Gooid luck

Designed by SA3CFY